About us    Contact us    |    

JZABM balacning machineHangzhou Jizhi Mechatronic Co.,ltd.
Balancing Machine Listed enterprise in China

VacuumCleanerImpellerBalancingMachine-DynamicBalancingMachineManufacturer-JZABM(Listedcompany)

Knowledge Base

Vacuum Cleaner Impeller Balancing Machine

The working principle of Hangzhou Jizhi Mechatronic Co., Ltd vacuum cleaner impeller balancing machine is to measure the unbalanced position of the impeller through the whole dynamic balancing machine. Then the weight of a certain position is too much or too little, so that the centrifugal force generated by the impeller in the rotating process is the same. Finally, the impeller does not vibrate as much as possible when rotating at high speed. Motor balancing machine of intelligent vacuum cleaner This product is a mechatronics device, and the new version of KV-7500 series is used as the main controller, which can greatly improve the response rate, complete the measurement of the rotor of the whole machine, and control the actions such as weight removal and balance.

For the special suction impeller rotor products, customized solutions can be supported. The main components are first-line brands, with stable and reliable equipment performance, high measurement data accuracy and good repeatability. Under production conditions, the equipment works continuously, the whole machine runs smoothly, and the beat meets the requirements. The fixture of vacuum cleaner is simple in design, easy to change lines, saves production time, and can be suitable for mass production.

Jizhi vacuum cleaner impeller balancing machine single processing station can be divided into measuring station, rotating station and heavy removing station. When working, the operator needs to manually load and unload the impeller rotor. Learn about the characteristics of each station with the following small series:

1. measuring station

Before this measuring station starts measuring, it is necessary to manually feed the rotor to complete the positioning. When measuring, the cylinder pushes against the rotor of the whole machine, the power supply cylinder supplies power upwards, and then the static unbalance is measured.

1. measuring station

Before this measuring station starts measuring, it is necessary to manually feed the rotor to complete the positioning. When measuring, the cylinder pushes against the rotor of the whole machine, the power supply cylinder supplies power upwards, and then the static unbalance is measured.

After the measurement, according to the calculated unbalance angle and value, the cylinder pushes and presses down, and the pressing block presses the rotor of the whole machine, which is driven by the stepping motor to rotate the blades of the whole machine to the corresponding angle.

3. Go to the heavy duty station.

According to the unbalance, the servo motor is used to drive the air shear through the electric cylinder to remove the unbalance. The heavy fines are collected automatically by the vacuum generator through the air pipe and the chip removing guide block.

The motor of the vacuum cleaner is the heart of the vacuum cleaner. The motor of the vacuum cleaner consists of two parts: the motor part and the fan part. Because the motor of the vacuum cleaner has a high requirement for rotating speed, generally 20,000-30,000 rpm, the motor is mainly series-excited motor. In order to improve the quality of the motor of the vacuum cleaner, manufacturers will carry out dynamic balance correction on the impeller rotor of the vacuum cleaner. The vacuum cleaner rotor balancing machine developed by Jizhi is suitable for the dynamic balance correction of most complete rotors with the diameter and outer diameter of blades of 30 mm ~ 120 mm. We usually see that some good vacuum cleaners are very safe when they work, and we can hardly feel the vibration of the machine when we hold them in our hands. When some vacuum cleaners with poor quality work, they can clearly see that they are shaking all over, and when they get their hands, they feel their hands shaking obviously.

Hangzhou Jizhi Electromechanical Co., Ltd. focuses on dynamic balancer R&D, design, production and sales, and strive to become an enterprise with comprehensive R&D and comprehensive application of balanced technology. Chi Electromechanical Co., Ltd., together with subsidiaries such as Shanghai Hengwang and Hangzhou Hehui, has built and extended the industrial chain structure, continuously increased the development of new products, actively explored and developed new energy industries, high-speed dynamic balancing and intelligent manufacturing fields such as aerospace, and provided customers with reliable and diversified product choices.

Prev:

Next:

Leave a message